• Source: Lithium ion manganese oxide battery

A lithium ion manganese oxide battery (LMO) is a lithium-ion cell that uses manganese dioxide, MnO2, as the cathode material. They function through the same intercalation/de-intercalation mechanism as other commercialized secondary battery technologies, such as LiCoO2. Cathodes based on manganese-oxide components are earth-abundant, inexpensive, non-toxic, and provide better thermal stability.




Compounds






= Spinel LiMn2O4

=
One of the more studied manganese oxide-based cathodes is LiMn2O4, a cation ordered member of the spinel structural family (space group Fd3m). In addition to containing inexpensive materials, the three-dimensional structure of LiMn2O4 lends itself to high rate capability by providing a well connected framework for the insertion and de-insertion of Li+ ions during discharge and charge of the battery. In particular, the Li+ ions occupy the tetrahedral sites within the Mn2O4 polyhedral frameworks adjacent to empty octahedral sites. As a consequence of this structural arrangement, batteries based on LiMn2O4 cathodes have demonstrated a higher rate-capability compared to materials with two-dimensional frameworks for Li+ diffusion.
A significant disadvantage of cathodes based on LiMn2O4 is the surface degradation observed when the average oxidation state of the manganese drops below Mn+3.5. At this concentration, the formally Mn(III) at the surface can disproportionate to form Mn(IV) and Mn(II) by the Hunter mechanism. The Mn(II) formed is soluble in most electrolytes and its dissolution degrades the cathode. With this in mind many manganese cathodes are substituted or doped to keep the average manganese oxidation state above +3.5 during battery use or they will suffer from lower overall capacities as a function of cycle life and temperature.




= Layered Li2MnO3

=
Li2MnO3 is a lithium rich layered rocksalt structure that is made of alternating layers of lithium ions and lithium and manganese ions in a 1:2 ratio, similar to the layered structure of LiCoO2. In the nomenclature of layered compounds it can be written Li(Li0.33Mn0.67)O2. Although Li2MnO3 is electrochemically inactive, it can be charged to a high potential (4.5 V v.s Li0) in order to undergo lithiation/de-lithiation or delithiated using an acid leaching process followed by mild heat treatment. However, extracting lithium from Li2MnO3 at such a high potential can also be charge compensated by loss of oxygen from the electrode surface which leads to poor cycling stability. New allotropes of Li2MnO3 have been discovered which have better structural stability against oxygen release (longer cycle-life).




= Layered LiMnO2

=
The layered manganese oxide LiMnO2 is constructed from corrugated layers of manganese/oxide octahedra and is electrochemically unstable. The distortions and deviation from truly planar metal oxide layers are a manifestation of the electronic configuration of the Mn(III) Jahn-Teller ion. A layered variant, isostructural with LiCoO2, was prepared in 1996 by ion exchange from the layered compound NaMnO2, however long term cycling and the defect nature of the charged compound led to structural degradation and cation equilibration to other phases.




= Layered Li2MnO2

=
The layered manganese oxide Li2MnO2 is structurally related to Li2MnO3 and LiCoO2 with similar transition metal oxide layers separated by a layer containing two lithium cations occupying the available two tetrahedral sites in the lattice rather the one octahedral site. The material is typically made by low voltage lithiation of the parent compound, direct lithiation using liquid ammonia, or via use of an organic lithiating reagent. Stability on cycling has been demonstrated in symmetric cells although due to Mn(II) formation and dissolution cycling degradation is expected. Stabilization of the structure using dopants and substitutions to decrease the amount of reduced manganese cations has been a successful route to extending the cycle life of these lithium rich reduced phases. These layered manganese oxide layers are so rich in lithium.




= x Li2MnO3 • y Li1+aMn2-aO4 • z LiMnO2 composites

=
One of the main research efforts in the field of lithium-manganese oxide electrodes for lithium-ion batteries involves developing composite electrodes using structurally integrated layered Li2MnO3, layered LiMnO2, and spinel LiMn2O4, with a chemical formula of x Li2MnO3 • y Li1+aMn2-aO4 • z LiMnO2, where x+y+z=1. The combination of these structures provides increased structural stability during electrochemical cycling while achieving higher capacity and rate-capability. A rechargeable capacity in excess of 250 mAh/g was reported in 2005 using this material, which has nearly twice the capacity of current commercialized rechargeable batteries of the same dimensions.




See also


List of battery types
List of battery sizes
Comparison of battery types




References

Kata Kunci Pencarian:

• Baterai ion litium
• Seng
• Vanadium
• John Bannister Goodenough
• Nikel
• Nonlogam
• Metaloid
• Lithium ion manganese oxide battery
• Lithium-ion battery
• Lithium battery
• Lithium metal battery
• Lithium iron phosphate battery
• Lithium-titanate battery
• Lithium nickel manganese cobalt oxides
• Sodium-ion battery
• Solid-state battery
• Lithium–air battery