• Source: Point-contact transistor

The point-contact transistor was the first type of transistor to be successfully demonstrated. It was developed by research scientists John Bardeen and Walter Brattain at Bell Laboratories in December 1947. They worked in a group led by physicist William Shockley. The group had been working together on experiments and theories of electric field effects in solid state materials, with the aim of replacing vacuum tubes with a smaller device that consumed less power.
The critical experiment, carried out on December 16, 1947, consisted of a block of germanium, a semiconductor, with two very closely spaced gold contacts held against it by a spring. Brattain attached a small strip of gold foil over the point of a plastic triangle—a configuration which is essentially a point-contact diode. He then carefully sliced through the gold at the tip of the triangle. This produced two electrically isolated gold contacts very close to each other.

The piece of germanium used a surface layer with an excess of electrons. When an electric signal traveled in through the gold foil, it injected electron holes (points which lack electrons). This created a thin layer which had a scarcity of electrons.
A small positive current applied to one of the two contacts had an influence on the current which flowed between the other contact and the base upon which the block of germanium was mounted. In fact, a small change in the first contact current caused a greater change in the second contact current; thus it was an amplifier. The low-current input terminal into the point-contact transistor is the emitter, while the output high current terminals are the base and collector. This differs from the later type of bipolar junction transistor invented in 1951 that operates as transistors still do, with the low current input terminal as the base and the two high current output terminals as the emitter and collector.
The point-contact transistor was commercialized and sold by Western Electric and others but was eventually superseded by the bipolar junction transistor, which was easier to manufacture and more rugged. The point-contact transistor did still remain in production until around 1966, by which time the silicon planar transistor was dominating the market.




Forming



While point-contact transistors usually worked fine when the metal contacts were simply placed close together on the germanium base crystal, it was desirable to obtain as high an α current gain as possible.
To obtain a higher α current gain in a point-contact transistor, a brief high-current pulse was used to modify the properties of the collector point of contact, a technique called 'electrical forming'. Usually this was done by charging a capacitor of a specified value to a specified voltage then discharging it between the collector and the base electrodes. Forming had a significant failure rate, so many commercial encapsulated transistors had to be discarded. While the effects of forming were understood empirically, the exact physics of the process could never be adequately studied and thus no clear theory was ever developed to explain it or provide guidance on improving it.
Unlike later semiconductor devices, it was possible for an amateur to make a point-contact transistor, starting with a germanium point-contact diode as a source of material (even a burnt-out diode could be used; and the transistor could be re-formed if damaged, several times if necessary).




Characteristics


Some characteristics of point-contact transistors differ from the slightly later junction transistors:

The common base current gain (or α) of a point-contact transistor is usually around 2 to 3, whereas α of bipolar junction transistor (BJT) cannot exceed 1. The common emitter current gain (or β) of a point-contact transistor does not usually exceed 1, whereas β of a BJT is typically between 20 and 200.
Negative differential resistance. Point contact transistors connected in the common emitter amplifier configuration will display negative output resistance, which may be undesirable for voltage/current amplifier applications. Switching circuits based around point contact transistors often rely on negative differential resistance.: 132, 149–163 
Until the development of the surface barrier transistor in 1953 point-contact transistors were the fastest transistors available,: 71, 267 : 227  some operating in the lower part of the VHF band when the fastest junction transistors could still only barely operate at a few MHz.
Moisture attack was less damaging to point-contact transistors than to junction transistors,: 386  because their collector reverse resistance is lower and cutoff collector current higher.
When used in the saturated mode in digital logic, in some circuit designs (but not all) they latched in the "on" state, making it necessary to remove power for a short time in each machine cycle to return them to the off-state.




See also


Crystal radio
Duodiode
Transistron




References






Further reading


Bardeen, J.; Brattain, W.H. (15 July 1948). "The Transistor, A Semiconductor Triode". Physical Review. 74 (2). American Physical Society: 230–231. Bibcode:1948PhRv...74..230B. doi:10.1103/physrev.74.230.




External links


The Point-contact Transistor
PBS article

Kata Kunci Pencarian:

• Transistor kontak titik
• Metaloid
• Wolfram
• Pentium III
• Daftar istilah fotografi
• Point-contact transistor
• Bipolar junction transistor
• Transistor
• History of the transistor
• Point contacts
• Walter Houser Brattain
• Field-effect transistor
• Semiconductor
• Fin field-effect transistor
• Insulated-gate bipolar transistor