- Source: Early effect
The Early effect, named after its discoverer James M. Early, is the variation in the effective width of the base in a bipolar junction transistor (BJT) due to a variation in the applied base-to-collector voltage. A greater reverse bias across the collector–base junction, for example, increases the collector–base depletion width, thereby decreasing the width of the charge carrier portion of the base.
Explanation
In Figure 1, the neutral (i.e. active) base is green, and the depleted base regions are hashed light green. The neutral emitter and collector regions are dark blue and the depleted regions hashed light blue. Under increased collector–base reverse bias, the lower panel of Figure 1 shows a widening of the depletion region in the base and the associated narrowing of the neutral base region.
The collector depletion region also increases under reverse bias, more than does that of the base, because the collector is less heavily doped than the base. The principle governing these two widths is charge neutrality. The narrowing of the collector does not have a significant effect as the collector is much longer than the base. The emitter–base junction is unchanged because the emitter–base voltage is the same.
Base-narrowing has two consequences that affect the current:
There is a lesser chance for recombination within the "smaller" base region.
The charge gradient is increased across the base, and consequently, the current of minority carriers injected across the collector-base junction increases, which net current is called
I
CB0
{\displaystyle I_{\text{CB0}}}
.
Both these factors increase the collector or "output" current of the transistor with an increase in the collector voltage, but only the second is called Early effect. This increased current is shown in Figure 2. Tangents to the characteristics at large voltages extrapolate backward to intercept the voltage axis at a voltage called the Early voltage, often denoted by the symbol VA.
Large-signal model
In the forward active region the Early effect modifies the collector current (
I
C
{\displaystyle I_{\mathrm {C} }}
) and the forward common-emitter current gain (
β
F
{\displaystyle \beta _{\mathrm {F} }}
), as typically described by the following equations:
I
C
=
I
S
e
V
B
E
V
T
(
1
+
V
C
E
V
A
)
β
F
=
β
F
0
(
1
+
V
C
E
V
A
)
{\displaystyle {\begin{aligned}I_{\mathrm {C} }&=I_{\mathrm {S} }e^{\frac {V_{\mathrm {BE} }}{V_{\mathrm {T} }}}\left(1+{\frac {V_{\mathrm {CE} }}{V_{\mathrm {A} }}}\right)\\\beta _{\mathrm {F} }&=\beta _{\mathrm {F0} }\left(1+{\frac {V_{\mathrm {CE} }}{V_{\mathrm {A} }}}\right)\end{aligned}}}
where
V
C
E
{\displaystyle V_{\mathrm {CE} }}
is the collector–emitter voltage
V
B
E
{\displaystyle V_{\mathrm {BE} }}
is the base–emitter voltage
I
S
{\displaystyle I_{\mathrm {S} }}
is the reverse saturation current
V
T
{\displaystyle V_{\mathrm {T} }}
is the thermal voltage
k
T
/
q
{\displaystyle \mathrm {kT/q} }
; see thermal voltage: role in semiconductor physics
V
A
{\displaystyle V_{\mathrm {A} }}
is the Early voltage (typically 15–150 V; less for smaller devices)
β
F
0
{\displaystyle \beta _{\mathrm {F0} }}
is forward common-emitter current gain at zero bias.
Some models base the collector current correction factor on the collector–base voltage VCB (as described in base-width modulation) instead of the collector–emitter voltage VCE. Using VCB may be more physically plausible, in agreement with the physical origin of the effect, which is a widening of the collector–base depletion layer that depends on VCB. Computer models such as those used in SPICE use the collector–base voltage VCB.
Small-signal model
The Early effect can be accounted for in small-signal circuit models (such as the hybrid-pi model) as a resistor defined as
r
O
=
V
A
+
V
CE
I
C
≈
V
A
I
C
{\displaystyle r_{\text{O}}={\frac {V_{\text{A}}+V_{\text{CE}}}{I_{\text{C}}}}\approx {\frac {V_{\text{A}}}{I_{\text{C}}}}}
in parallel with the collector–emitter junction of the transistor. This resistor can thus account for the finite output resistance of a simple current mirror or an actively loaded common-emitter amplifier.
In keeping with the model used in SPICE and as discussed above using
V
C
B
{\displaystyle V_{CB}}
the resistance becomes:
r
O
=
V
A
+
V
CB
I
C
{\displaystyle r_{\text{O}}={\frac {V_{\text{A}}+V_{\text{CB}}}{I_{\text{C}}}}}
which almost agrees with the textbook result. In either formulation,
r
O
{\displaystyle r_{O}}
varies with DC reverse bias
V
C
B
{\displaystyle V_{CB}}
, as is observed in practice.
In the MOSFET the output resistance is given in Shichman–Hodges model (accurate for very old technology) as:
r
O
=
1
+
λ
V
DS
λ
I
D
=
1
I
D
(
1
λ
+
V
DS
)
{\displaystyle r_{\text{O}}={\frac {1+\lambda V_{\text{DS}}}{\lambda I_{\text{D}}}}={\frac {1}{I_{\text{D}}}}\left({\frac {1}{\lambda }}+V_{\text{DS}}\right)}
where
V
DS
{\displaystyle V_{\text{DS}}}
= drain-to-source voltage,
I
D
{\displaystyle I_{\text{D}}}
= drain current and
λ
{\displaystyle \lambda }
= channel-length modulation parameter, usually taken as inversely proportional to channel length L.
Because of the resemblance to the bipolar result, the terminology "Early effect" often is applied to the MOSFET as well.
= Current–voltage characteristics
=The expressions are derived for a PNP transistor. For an NPN transistor, n has to be replaced by p, and p has to be replaced by n in all expressions below.
The following assumptions are involved when deriving ideal current-voltage characteristics of the BJT
Low level injection
Uniform doping in each region with abrupt junctions
One-dimensional current
Negligible recombination-generation in space charge regions
Negligible electric fields outside of space charge regions.
It is important to characterize the minority diffusion currents induced by injection of carriers.
With regard to pn-junction diode, a key relation is the diffusion equation.
d
2
Δ
p
B
(
x
)
d
x
2
=
Δ
p
B
(
x
)
L
B
2
{\displaystyle {\frac {d^{2}\Delta p_{\text{B}}(x)}{dx^{2}}}={\frac {\Delta p_{\text{B}}(x)}{L_{\text{B}}^{2}}}}
A solution of this equation is below, and two boundary conditions are used to solve and find
C
1
{\displaystyle C_{1}}
and
C
2
{\displaystyle C_{2}}
.
Δ
p
B
(
x
)
=
C
1
e
x
L
B
+
C
2
e
−
x
L
B
{\displaystyle \Delta p_{\text{B}}(x)=C_{1}e^{\frac {x}{L_{\text{B}}}}+C_{2}e^{-{\frac {x}{L_{\text{B}}}}}}
The following equations apply to the emitter and collector region, respectively, and the origins
0
{\displaystyle 0}
,
0
′
{\displaystyle 0'}
, and
0
″
{\displaystyle 0''}
apply to the base, collector, and emitter.
Δ
n
B
(
x
″
)
=
A
1
e
x
″
L
B
+
A
2
e
−
x
″
L
B
Δ
n
c
(
x
′
)
=
B
1
e
x
′
L
B
+
B
2
e
−
x
′
L
B
{\displaystyle {\begin{aligned}\Delta n_{\text{B}}(x'')&=A_{1}e^{\frac {x''}{L_{\text{B}}}}+A_{2}e^{-{\frac {x''}{L_{\text{B}}}}}\\\Delta n_{\text{c}}(x')&=B_{1}e^{\frac {x'}{L_{\text{B}}}}+B_{2}e^{-{\frac {x'}{L_{\text{B}}}}}\end{aligned}}}
A boundary condition of the emitter is below:
Δ
n
E
(
0
″
)
=
n
E
O
(
e
1
k
T
q
V
EB
−
1
)
{\displaystyle \Delta n_{\text{E}}(0'')=n_{{\text{E}}O}\left(e^{{\frac {1}{kT}}qV_{\text{EB}}}-1\right)}
The values of the constants
A
1
{\displaystyle A_{1}}
and
B
1
{\displaystyle B_{1}}
are zero due to the following conditions of the emitter and collector regions as
x
″
→
0
{\displaystyle x''\rightarrow 0}
and
x
′
→
0
{\displaystyle x'\rightarrow 0}
.
Δ
n
E
(
x
″
)
→
0
Δ
n
c
(
x
′
)
→
0
{\displaystyle {\begin{aligned}\Delta n_{\text{E}}(x'')&\rightarrow 0\\\Delta n_{\text{c}}(x')&\rightarrow 0\end{aligned}}}
Because
A
1
=
B
1
=
0
{\displaystyle A_{1}=B_{1}=0}
, the values of
Δ
n
E
(
0
″
)
{\displaystyle \Delta n_{\text{E}}(0'')}
and
Δ
n
c
(
0
′
)
{\displaystyle \Delta n_{\text{c}}(0')}
are
A
2
{\displaystyle A_{2}}
and
B
2
{\displaystyle B_{2}}
, respectively.
Δ
n
E
(
x
″
)
=
n
E
0
(
e
q
V
EB
k
T
−
1
)
e
−
x
″
L
E
Δ
n
C
(
x
′
)
=
n
C
0
(
e
q
V
CB
k
T
−
1
)
e
−
x
′
L
C
{\displaystyle {\begin{aligned}\Delta n_{\text{E}}(x'')&=n_{{\text{E}}0}\left(e^{\frac {qV_{\text{EB}}}{kT}}-1\right)e^{-{\frac {x''}{L_{\text{E}}}}}\\\Delta n_{\text{C}}(x')&=n_{{\text{C}}0}\left(e^{\frac {qV_{\text{CB}}}{kT}}-1\right)e^{-{\frac {x'}{L_{\text{C}}}}}\end{aligned}}}
Expressions of
I
E
n
{\displaystyle I_{{\text{E}}n}}
and
I
C
n
{\displaystyle I_{{\text{C}}n}}
can be evaluated.
I
E
n
=
−
q
A
D
E
d
Δ
E
(
x
″
)
d
x
|
x
″
=
0
″
I
C
n
=
−
q
A
D
C
L
C
n
C
0
(
e
q
V
CB
k
T
−
1
)
{\displaystyle {\begin{aligned}I_{{\text{E}}n}&=\left.-qAD_{\text{E}}{\frac {d\Delta _{\text{E}}(x'')}{dx}}\right|_{x''=0''}\\I_{{\text{C}}n}&=-qA{\frac {D_{\text{C}}}{L_{\text{C}}}}n_{{\text{C}}0}\left(e^{\frac {qV_{\text{CB}}}{kT}}-1\right)\end{aligned}}}
Because insignificant recombination occurs, the second derivative of
Δ
p
B
(
x
)
{\displaystyle \Delta p_{\text{B}}(x)}
is zero. There is therefore a linear relationship between excess hole density and
x
{\displaystyle x}
.
Δ
p
B
(
x
)
=
D
1
x
+
D
2
{\displaystyle \Delta p_{\text{B}}(x)=D_{1}x+D_{2}}
The following are boundary conditions of
Δ
p
B
{\displaystyle \Delta p_{\text{B}}}
.
Δ
p
B
(
0
)
=
D
2
Δ
p
B
(
W
)
=
D
1
W
+
Δ
p
B
(
0
)
{\displaystyle {\begin{aligned}\Delta p_{\text{B}}(0)&=D_{2}\\\Delta p_{\text{B}}(W)&=D_{1}W+\Delta p_{\text{B}}(0)\end{aligned}}}
with W the base width. Substitute into the above linear relation.
Δ
p
B
(
x
)
=
−
1
W
[
Δ
p
B
(
0
)
−
Δ
p
B
(
W
)
]
x
+
Δ
p
B
(
0
)
{\displaystyle \Delta p_{\text{B}}(x)=-{\frac {1}{W}}\left[\Delta p_{\text{B}}(0)-\Delta p_{\text{B}}(W)\right]x+\Delta p_{\text{B}}(0)}
With this result, derive value of
I
E
p
{\displaystyle I_{{\text{E}}p}}
.
I
E
p
(
0
)
=
−
q
A
D
B
d
Δ
p
B
d
x
|
x
=
0
I
E
p
(
0
)
=
q
A
D
B
W
[
Δ
p
B
(
0
)
−
Δ
p
B
(
W
)
]
{\displaystyle {\begin{aligned}I_{{\text{E}}p}(0)&=\left.-qAD_{\text{B}}{\frac {d\Delta p_{\text{B}}}{dx}}\right|_{x=0}\\I_{{\text{E}}p}(0)&={\frac {qAD_{\text{B}}}{W}}\left[\Delta p_{\text{B}}(0)-\Delta p_{\text{B}}(W)\right]\end{aligned}}}
Use the expressions of
I
E
p
{\displaystyle I_{{\text{E}}p}}
,
I
E
n
{\displaystyle I_{{\text{E}}n}}
,
Δ
p
B
(
0
)
{\displaystyle \Delta p_{\text{B}}(0)}
, and
Δ
p
B
(
W
)
{\displaystyle \Delta p_{\text{B}}(W)}
to develop an expression of the emitter current.
Δ
p
B
(
W
)
=
p
B
0
e
q
V
CB
k
T
Δ
p
B
(
0
)
=
p
B
0
e
q
V
EB
k
T
I
E
=
q
A
[
(
D
E
n
E
0
L
E
+
D
B
p
B
0
W
)
(
e
q
V
EB
k
T
−
1
)
−
D
B
W
p
B
0
(
e
q
V
CB
k
T
−
1
)
]
{\displaystyle {\begin{aligned}\Delta p_{\text{B}}(W)&=p_{{\text{B}}0}e^{\frac {qV_{\text{CB}}}{kT}}\\\Delta p_{\text{B}}(0)&=p_{{\text{B}}0}e^{\frac {qV_{\text{EB}}}{kT}}\\I_{\text{E}}&=qA\left[\left({\frac {D_{\text{E}}n_{{\text{E}}0}}{L_{\text{E}}}}+{\frac {D_{\text{B}}p_{{\text{B}}0}}{W}}\right)\left(e^{\frac {qV_{\text{EB}}}{kT}}-1\right)-{\frac {D_{\text{B}}}{W}}p_{{\text{B}}0}\left(e^{\frac {qV_{\text{CB}}}{kT}}-1\right)\right]\end{aligned}}}
Similarly, an expression of the collector current is derived.
I
C
p
(
W
)
=
I
E
p
(
0
)
I
C
=
I
C
p
(
W
)
+
I
C
n
(
0
′
)
I
C
=
q
A
[
D
B
W
p
B
0
(
e
q
V
EB
k
T
−
1
)
−
(
D
C
n
C
0
L
C
+
D
B
p
B
0
W
)
(
e
q
V
CB
k
T
−
1
)
]
{\displaystyle {\begin{aligned}I_{{\text{C}}p}(W)&=I_{{\text{E}}p}(0)\\I_{\text{C}}&=I_{{\text{C}}p}(W)+I_{{\text{C}}n}(0')\\I_{\text{C}}&=qA\left[{\frac {D_{\text{B}}}{W}}p_{{\text{B}}0}\left(e^{\frac {qV_{\text{EB}}}{kT}}-1\right)-\left({\frac {D_{\text{C}}n_{{\text{C}}0}}{L_{\text{C}}}}+{\frac {D_{\text{B}}p_{{\text{B}}0}}{W}}\right)\left(e^{\frac {qV_{\text{CB}}}{kT}}-1\right)\right]\end{aligned}}}
An expression of the base current is found with the previous results.
I
B
=
I
E
−
I
C
I
B
=
q
A
[
D
E
L
E
n
E
0
(
e
q
V
EB
k
T
−
1
)
+
D
C
L
C
n
C
0
(
e
q
V
CB
k
T
−
1
)
]
{\displaystyle {\begin{aligned}I_{\text{B}}&=I_{\text{E}}-I_{\text{C}}\\I_{\text{B}}&=qA\left[{\frac {D_{\text{E}}}{L_{\text{E}}}}n_{{\text{E}}0}\left(e^{\frac {qV_{\text{EB}}}{kT}}-1\right)+{\frac {D_{\text{C}}}{L_{\text{C}}}}n_{{\text{C}}0}\left(e^{\frac {qV_{\text{CB}}}{kT}}-1\right)\right]\end{aligned}}}
References and notes
See also
Small-signal model
Kata Kunci Pencarian:
- Joko Widodo
- Globalisasi
- X (media sosial)
- Histogram
- MOSFET
- Rencana Jackson
- Taman kanak-kanak
- Asam traneksamat
- Dunia Fantasi
- Sistem imun
- Early effect
- Early
- List of effects
- Streisand effect
- Current mirror
- Mass Effect
- Channel length modulation
- Photoelectric effect
- Butterfly effect
- Early modern period
