• Source: Laser construction

A laser is constructed from three principal parts:

An energy source (usually referred to as the pump or pump source),
A gain medium or laser medium, and
Two or more mirrors that form an optical resonator.




Pump source


The pump source is the part that provides energy to the laser system. Examples of pump sources include electrical discharges, flashlamps, arc lamps, light from another laser, chemical reactions and even explosive devices. The type of pump source used principally depends on the gain medium, and this also determines how the energy is transmitted to the medium. A helium–neon (HeNe) laser uses an electrical discharge in the helium-neon gas mixture, a Nd:YAG laser uses either light focused from a xenon flash lamp or diode lasers, and excimer lasers use a chemical reaction.




Gain medium / Laser medium


The gain medium is the major determining factor of the wavelength of operation, and other properties, of the laser. Gain media in different materials have linear spectra or wide spectra. Gain media with wide spectra allow tuning of the laser frequency. There are hundreds if not thousands of different gain media in which laser operation has been achieved (see list of laser types for a list of the most important ones). The gain medium is excited by the pump source to produce a population inversion, and it is in the gain medium where spontaneous and stimulated emission of photons takes place, leading to the phenomenon of optical gain, or amplification.
Examples of different gain media include:

Liquids, such as dye lasers. These are usually organic chemical solvents, such as methanol, ethanol or ethylene glycol, to which are added chemical dyes such as coumarin, rhodamine, and fluorescein. The exact chemical configuration of the dye molecules determines the operation wavelength of the dye laser.
Gases, such as carbon dioxide, argon, krypton and mixtures such as helium–neon. These lasers are often pumped by electrical discharge.
Solids, such as crystals and glasses. The solid host materials are usually doped with an impurity such as chromium, neodymium, erbium or titanium ions. Typical hosts include YAG (yttrium aluminium garnet), YLF (yttrium lithium fluoride), sapphire (aluminium oxide) and various glasses. Examples of solid-state laser media include Nd:YAG, Ti:sapphire, Cr:sapphire (usually known as ruby), Cr:LiSAF (chromium-doped lithium strontium aluminium fluoride), Er:YLF, Nd:glass, and Er:glass. Solid-state lasers are usually pumped by flashlamps or light from another laser.
Semiconductors, a type of solid, crystal with uniform dopant distribution or material with differing dopant levels in which the movement of electrons can cause laser action. Semiconductor lasers are typically very small, and can be pumped with a simple electric current, enabling them to be used in consumer devices such as compact disc players. See laser diode.




Optical resonator



The optical resonator, or optical cavity, in its simplest form is two parallel mirrors placed around the gain medium, which provide feedback of the light. The mirrors are given optical coatings which determine their reflective properties. Typically, one will be a high reflector, and the other will be a partial reflector. The latter is called the output coupler, because it allows some of the light to leave the cavity to produce the laser's output beam.
Light from the medium, produced by spontaneous emission, is reflected by the mirrors back into the medium, where it may be amplified by stimulated emission. The light may reflect from the mirrors and thus pass through the gain medium many hundreds of times before exiting the cavity. In more complex lasers, configurations with four or more mirrors forming the cavity are used. The design and alignment of the mirrors with respect to the medium is crucial for determining the exact operating wavelength and other attributes of the laser system.
Other optical devices, such as spinning mirrors, modulators, filters, and absorbers, may be placed within the optical resonator to produce a variety of effects on the laser output, such as altering the wavelength of operation or the production of pulses of laser light.
Some lasers do not use an optical cavity, but instead rely on very high optical gain to produce significant amplified spontaneous emission (ASE) without needing feedback of the light back into the gain medium. Such lasers are said to be superluminescent, and emit light with low coherence but high bandwidth. Since they do not use optical feedback, these devices are often not categorized as lasers.




See also


Injection seeder
Mode locking
Q-switching
List of laser articles




References


Koechner, Walter (1992). Solid-State Laser Engineering, 3rd ed., Springer-Verlag. ISBN 0-387-53756-2




External links


Sam's Laser FAQ A Practical Guide to Lasers for Experimenters and Hobbyists

Kata Kunci Pencarian:

• Laser
• Komatsu Limited
• Maxell
• AMX-13
• Daftar anggota Decepticon
• Extremely Large Telescope
• Kapal perusak Type 052D
• Marina Bay Sands
• Daftar anggota Autobot
• Jalan Tol Lingkar Pekanbaru
• Laser construction
• Tactical High Energy Laser
• List of laser types
• Laser (dinghy)
• Laser
• Ring laser gyroscope
• Laser science
• Laser level
• Active laser medium
• Solid-state laser