- Source: Singer Bantam
The Singer Bantam is a car which was produced by Singer from 1936 to 1939. It was the first model from Singer to have an all-steel body, by Pressed Steel Company. It was offered as a new economy model at the 1935 Motor Show in London, replacing the earlier Singer Nine series.
History
Derived from the Singer Nine, with styling a close copy of the Ford Model Y, it debuted with two models and two trim levels: 2- and 4-door, either Popular or De-Luxe. All four shared the same basic bodyshell but, whereas the De-Luxe models had a sliding sunroof, the Popular version had a fixed panel in the roof. Other features of the De-Luxe model were leather seats, chrome bumpers, and a rear luggage rack.
The Bantam re-used many existing components from the Singer parts bin. It used the Le Mans' underslung chassis and 972 cc overhead cam engine, although with a lower compression ratio and single Solex carburettor. Power transmission was through a three-speed manual gearbox with synchromesh on third gear. Early models were equipped with wire wheels, while the optional easyclene wheels became standard from 1937. A chromed mascot portraying a flying Bantam chicken was mounted on the radiator surround until this was outlawed by new legislation in 1937.
For 1937 a Tourer model was announced, although few were made and very few survive. The Saloon got an upgrade in 1937 for the 1938 model year. The chassis and suspension were strengthened to take the larger 1074 cc inline-four engine with a stated 30 hp of output, and the brakes were converted to a cable system. The bodyshell remained the same apart from an extra chrome trim strip across the doors and changes to the bonnet louvres.
Many Bantams survive in Australia and New Zealand. Singer exported these vehicles as rolling chassis with complete powertrain. They were mainly bodied by the Flood company in Australia as tourers and roadsters, and this seems to have prompted the development of the roadster model by Singer in 1939, based on the Bantam chassis and engine.
Brakes, suspension and steering
The four-wheel brakes are operated hydraulically. They are designed on the Lockheed system. There is also a hand lever fitted with a sensibly shaped trigger to control the back brakes. The springs front and back are half-elliptical with oilite bearings and double-action hydraulic shock absorbers. The rear suspension like the frame passes below the axle. Steering is by worm and nut in a box held by a bracket to the frame.
Road test
The Times' correspondent reported that the engine pulls strongly and quickly lifts vehicle speed. Though not as quiet as a side-valve it sounds and feels efficient. The change speed lever was a little stiff and vague in action. A slight pause is necessary when changing gear to allow the synchromesh to do its job. The brakes proved effective though they pulled towards the nearside. The driver's position is excellent. "The accelerator might be cranked a little more to the right for the benefit of a large and heavy-footed driver". A comfortable top speed (in poor gusty weather) was 60 mph (97 km/h).
Motor sport
Tom Brady won the 1939 Australian Stock Car Road Championship driving a Singer Bantam.
Roadster
In 1939 Singer decided that they needed a more comfortable, but still sporting model in their lineup. Thus, the open four-seater Nine Roadster appeared 6 March 1939 with a lightly tuned version of the larger 1074 cc overhead camshaft engine already seen in the Bantam Nine, as well as that car's three-speed gearbox. In September 1949 the name was changed to Singer 9 Roadster series 4A to herald the introduction of a four-speed transmission, but the model continued to be built in 1.1 litre form until 1953 and in 1½-litre form as Singer SM Roadster until 1955.
References
Kata Kunci Pencarian:
5.3
6.5
7.987
6.3
7.501
7.43
6.9
7.329
7.4
6
No More Posts Available.
No more pages to load.
