- Source: Transversal (instrument making)
Transversals are a geometric construction on a scientific instrument to allow a graduation to be read to a finer degree of accuracy. Their use creates what is sometimes called a diagonal scale, an engineering measuring instrument which is composed of a set of parallel straight lines which are obliquely crossed by another set of straight lines. Diagonal scales are used to measure small fractions of the unit of measurement.
Transversals have been replaced in modern times by vernier scales. This method is based on the Intercept theorem (also known as Thales's theorem).
History
Transversals were used at a time when finely graduated instruments were difficult to make. They were found on instruments starting in the early 14th century, but the inventor is unknown. In 1342 Levi Ben Gerson introduced an instrument called Jacob's staff (apparently invented the previous century by Jacob Ben Makir) and described the method of the transversal scale applied to the mentioned instrument.
Thomas Digges mistakenly attributed the discovery of the transversal scale to the navigator and explorer Richard Chancellor (cited by some authors as watchmaker and with other names, among them: Richard Chansler or Richard Kantzler). Its use on astronomical instruments only began in the late 16th century. Tycho Brahe used them and did much to popularize the technique. The technique began to die out once verniers became common in the late 18th century – over a century after Pierre Vernier introduced the technique.
In the interim between transversals and the vernier scale, the nonius system, developed by Pedro Nunes, was used. However, it was never in common use. Tycho also used nonius methods, but he appears to be the only prominent astronomer to do so.
Etymology
Diagonal scale is derived from the Latin word Diagonalis. The Latin word was originally coined from the Greek word diagōnios where dia means "through" and gonios denotes "corners".
Principle of a diagonal scale
Diagonal scale follows the principle of similar triangles where a short length is divided into number of parts in which sides are proportional.
Divided into required number of equal parts
Linear transversals
Linear transversals were used on linear graduations. A grid of lines was constructed immediately adjacent to the linear graduations. The lines extending above the graduations formed part of the grid. The number of lines perpendicular to the extended graduation lines in the grid was dependent on the degree of fineness the instrument maker wished to provide.
A grid of five lines would permit determination of the measure to one-fifth of a graduation's division. A ten-line grid would permit tenths to be measured. The distance between the lines is not critical as long as the distance is precisely uniform. Greater distances makes for greater accuracy.
As seen in the illustration on the right, once the grid was scribed, diagonals (transverse lines) were scribed from the uppermost corner of a column in the grid to the opposite lowest corner. This line intersects the cross lines in the grid in equal intervals. By using an indicator such as a cursor or alidade, or by measuring using a pair of dividers with points on the same horizontal grid line, the closest point where the transversal crosses the grid is determined. That indicates the fraction of the graduation for the measure.
In the illustration, the reading is indicated by the vertical red line. This could be the edge of an alidade or a similar device. Since the cursor crosses the transversal closest to the fourth grid line from the top, the reading (assuming the leftmost long graduation line is 0.0) is 0.54.
Application
Diagonal scale is used in engineering to read lengths with higher accuracy as it represents a unit into three different multiple in metres, centimeters and millimeters. Diagonal scale is an important part in Engineering drawings.
Circular transversals
Circular transversals perform the same function as the linear ones but for circular arcs. In this case, the construction of the grid is significantly more complicated. A rectangular grid will not work. A grid of radial lines and circumferential arcs must be created. In addition, a linear transverse line will not divide the radial grid into equal segments. Circular arc segments must be constructed as transversals to provide the correct proportions.
= Tycho Brahe
=Tycho Brahe created a grid of transversal lines made with secants between two groups of arcs that form two graduated limbs. The secants are drawn by joining the division of a limb with the next division of the other limb, and so on (see figure with the magnification of 2 degrees of the Tycho Brahe's quadrant of 2m radius).
He drew, for each degree, six straight transversals in an alternate mode forming a "V" and each transversal consisted of 9 points that divided it into 10 parts, which multiplied by 6 give 60 minutes. While Abd al-Mun'im al 'Âmilî (16th century) drew them all in the same direction (although his instrument has less precision).
= Other authors
=The method of the "straight transversals" applied to the measurements of angles on circular or semicircular limbs in astronomical and geographic instruments was treated by several authors. Studying the accuracy of the system, some of them indicated the convenience of employing "Circular transversals", instead of the "straight transversals".
See also
Micrometer
Vernier scale
References
Bibliography
Daumas, Maurice, Scientific Instruments of the Seventeenth and Eighteenth Centuries and Their Makers, Portman Books, London 1989 ISBN 978-0-7134-0727-3
Van Poelje, Otto E. (2004). "Diagonals and Transversals: Magnifying the Scale" (PDF). Journal of the Oughtred Society. 13 (2): 22–28.
External links
Thin Strip Jig with Transversal Scale